View GBPC1210_151427.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

GBPC12, 15, 25 AND 35 SERIES
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts Current Voltage - 12.0 to 35.0 Amperes
GBPC - W Wire leads
GBPC - Standard
The plastic package has Underwriters Laboratory Flammability Classification 94V-0 This series is UL recognized under component index, file number E54214 Integrally molded heatsink provides very low thermal resistance for maximum heat dissipation Universal 3-way terminals; snap-on, wire wrap-around, or P.C.B. mounting High forward surge current capabilities Glass passivated chip junctions Typical IR less than 0.3A High temperature soldering guaranteed: 260C/10 seconds at 5lbs. (2.3 kg) tension
FEATURES
MECHANICAL DATA
Case: Molded plastic with heatsink integrally mounted in the bridge encapsulation Terminals: Either plated 0.25" (6.35mm). Faston lugs or plated copper leads 0.040" (1.02mm) diameter. Suffix letter "W" added to indicate leads (e.g. GBPC12005W). Mounting Position: See NOTE 3 Polarity: Polarity symbols molded on body Mounting Torque: 20 in. - lb. max. Weight: 0.53 ounce, 15 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
SYMBOLS
005
01
GBPC12, 15, 25, 35 02 04 06
08
10
UNITS
Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified output current
(SEE FIG.1)
VRRM VRMS VDC
50 35 50
100 70 100
200 140 200
400 280 400 12.0 15.0 25.0 35.0 200.0 300.0 300.0 400.0 160.0 375.0 375.0 660.0 1.1
600 420 600
800 560 800
1000 700 1000
Volts Volts Volts Amps
GBPC12 GBPC15 GBPC25 GBPC35 GBPC12 GBPC15 GBPC25 GBPC35 GBPC12 GBPC15 GBPC25 GBPC35 GBPC12 GBPC15 GBPC25 GBPC35 IF=6.0A IF=7.5A IF=12.5A IF=17.5A TA=25C TA=125C
I(AV)
Peak forward surge current single sine-wave superimposed on rated load (JEDEC Method) Rating (non-repetitive, for t greater than 1ms and less than 8.3ms) for fusing Maximum instantaneous forward voltage drop per leg at
IFSM
Amps
I2t
A2 sec
VF
Volts
Maximum reverse DC current at rated DC blocking voltage per leg RMS isolation voltage from case to leads Typical junction capacitance per leg (NOTE 1)
IR VISO CJ RJC TJ, TSTG
5.0 500.0 2500.0 300.0 1.9 1.4 -55 to +150
A Volts pF C/W C
Typical thermal resistance per leg (NOTE 2) GBPC12-25 GBPC35 Operating junction storage temperature range
NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Thermal resistance from junction to case per leg (3) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer efficiency with #10 screw 7/28/98
RATINGS AND CHARACTERISTICS CURVES GBPC12, 15, 25 AND 35 SERIES
FIG. 1 - MAXIMUM OUTPUT RECTIFIED CURRENT
40
GBPC35
FIG. 2 - MAXIMUM OUTPUT RECTIFIED CURRENT
BRIDGES MOUNTED on 9 x 3.5 x 4.6" (22.9 x 8.9 x 11.7cm) AL. FINNED PLATE 5 x 6 x 4.9" AL. FINNED PLATE 5 x 4 x 3" AL. FINNED PLATE
40
RthS-A=0.5 C/W
35
AVERAGE FORWARD CURRENT, AMPERES
30
GBPC25
AVERAGE FORWARD CURRENT, AMPERES
35 30 25 20 15 10 5 0 0
GBPC35 GBPC25 RthS-A=0.5 C/W
60 HZ RESISTIVE OR INDUCTIVE LOAD
25 20
GBPC15
GBPC15 RthS-A=1.0 C/W
15
GBPC12
10 5 0
60 Hz RESISTIVE OR INDUCTIVE LOAD
6.0 x 2.2 x 2.2" AL. FINNED PLATE
GBPC12 RthS-A=1.0 C/W
0
25
50
75 100 125 150 175 200
10
20
30
40
50
60
70
80
90
100
AMBIENT TEMPERATURE, C CASE TEMPERATURE, C
FIG. 3 - MAXIMUM POWER DISSIPATION
FIG. 4 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG
80
CAPACITIVE LOAD
500
PEAK FORWARD SURGE CURRENT, AMPERES
TJ=TJ max. 0.5Single Sine-Wave (JEDEC Method) GBPC35 GBPC15 GBPC25
AVERAGE POWER DISSIPATION OF BRIDGE, WATTS
70 60 50 40 30 20 10 0
TJ=TJ max.
100
RESISTIVE OR INDUCTIVE LOAD
GBPC12 1.0 CYCLE
1
10
NUMBER OF CYCLES AT 60Hz
100
0
10
20
30
40
AVERAGE OUTPUT CURRENT, AMPERES
RATINGS AND CHARACTERISTICS CURVES GBPC12, 15, 25 AND 35 SERIES
FIG. 6 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG FIG. 5 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG
100
INSTANTANEOUS FORWARD CURRENT, AMPERES
TJ=125C
100
TJ=150C
10
INSTANTANEOUS REVERSE CURRENT, MICROAMPERES
50-400V 600-1000V
10
1
TJ=25C PULSE WIDTH=300s 1% DUTY CYCLE
0.1
1
0.01 0.4
0.6
0.8
1
1.2
1.4
1.6
0.1
TJ=25C
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
0.01
0
20
40
60
80
100
PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 7 - TYPICAL JUNCTION CAPACITANCE PER LEG
600
TRANSIENT THERMAL IMPEDANCE, C/W
TJ=25C f=1.0 MHz Vsig=50mVp-p
FIG. 8 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG
100
TJ=25C f=1.0 MHz Vsig=50mVp-p
JUNCTION, CAPACITANCE, pF
10
100
1
50
1
10
REVERSE VOLTAGE, VOLTS
100
0.1 0.01
0.1
1
t, HEATING TIME, sec.
10
100
FIG. 9
Hole for #10 Screw 0.220 (5.59) DIA. 0.200 (5.08)
GBPC
1.135 (28.8) 1.115 (28.3)
0.672 (17.1) 0.632 (16.1) AC
1.135 (28.8) 1.115 (28.3)
0.672 (17.1) 0.632 (16.1)
0.582 (14.8) 0.542 (13.8)
0.732 (18.6) 0.692 (17.6)
0.094 (2.4) DIA. 0.034 (0.86) 0.030 (0.76) 0.25 (6.35)
0.840 (21.3) 0.740 (18.8) 0.310 (7.62) 0.290 (7.36)
FIG. 10
GBPC-W
1.135 (28.8) Hole for #10 Screw 0.220 (5.59) DIA. 0.200 (5.08) 1.115 (28.3)
0.732 (18.6) 0.692 (17.6)
0.24 (6.0) 0.18 (4.6)
1.135 (28.8) 1.115 (28.3)
0.732 (18.6) 0.692 (17.6)
0.24 (6.0) 0.18 (4.6)
0.470 (11.9) 0.430 (10.9)
0.50 (12.7) 0.44 (11.7)
0.042 (1.07) 0.038 (0.97) DIA. 1.25 (31.8) MIN. 0.310 (7.62) 0.290 (7.36)
Dimensions in inches and (millimeters)
NOTES: (1) Corrosion resistant terminals designed with 0.25" female quick connectors for wrap or snap-on (2) A thin film of silicone thermal compound is recommended between the bridge case and mounting surface for improved thermal conduction

▲Up To Search▲

Price & Availability of GBPC1210

	To Download GBPC1210 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .